| Braunston Marina Ltd | |
| Braunston Marina Ltd, The Wharf Braunston, Daventry, Northamton, NN11 7JH, UK | |
| Contact: | Adrian Wilkins |
| View All Braunston Marina Ltd Listings | |
| £94,950 | | |
| Status: | Available |
| Tax Status: | Tax Exempt |
| Location: |
Braunston UK [View Map] |
| Reference: | CALBOURNE |
60ft, Trad Stern Narrowboat built in 2018 by XR& D.
FOR FULL DETAILS AND A 360 DEGREE VIDEO TOUR, PLEASE VISIT www.braunstonmarina.co.uk.
| Vessel name: | Calbourne |
| Condition: | Used |
| Vessel type: | Narrowboat |
| Builder: | XR&D |
| Make: | XR&D |
| Model: | 60 Traditional |
| Constructed: | 2018 |
| Registration: | 526440 |
| Berths: | 2 |
| Cabins: | 1 |
| Heads: | 1 |
| No. of engines: | 1 |
| Engine model: | GARDNER |
| Engine power: | 42hp |
| Fuel type: | Diesel |
| Length over all: | 60' |
| Beam: | 6' 10" |
| Hull material: | Steel |
| Hull type: | Flat |
| Hull colour: | Black |
| Fuel capacity: | 1000 Litres |
| Water capacity: | 700 Litres |
Saloon
With 2-seat leather recliner sofa, corner storage unit and step with storage. Breakfast bar and bar stool. If required, it would be possible to install a solid fuel stove here, as the chimney port is already cut through the roof. A 32” HD TV and Alexa-enabled Sonos Beam system provide entertainment. Access to domestic water pump unit and master fuel cut-off valve. Wall lights.
Galley
Comprising a range of craftsman-made units with curved doors, made from solid ash and birch ply, with 40mm solid iroko worktops. Additional drawers are located in the plinths. All drawers are soft close and have concealed runners. There are pull-down spice racks under the wall unit, which houses a Breville microwave. A 240V larder fridge is located next to a breakfast bar with bar stool. Sink unit with Franke 1.5 bowl granite resin sink and mixer tap. 2-ring induction hob.
The star of the galley, though, is the magnificent diesel-fired Sandyford Cottage cooker with twin hotplates, a huge top oven and simmering oven. Twin burners mean the cooker can operate independently as a hot water/heating boiler, or both. The oil burners are standard domestic pressure heating type, fitted with diesel preheaters. They can be serviced by any OFTEC engineer.
Bedroom
Containing a full 4’ 6” double bed with 30cm Shire Bed 2,000-spring mattress. The bed is mounted on gas struts, which allow it to be lifted to reveal a large storage space under. Reading lights over the bed and a handy bookshelf on iron brackets. There is also a useful cupboard, which is in fact the ‘dead’ corner of the kitchen unit. Solid oak bulkheads.
Bathroom
1200mm x 800mm quadrant shower with glass enclosure, with Hans Grohe twin head shower and thermostatic mixer. Wash basin on vanity unit, additional corner cupboard and Compoost separator toilet, vented to the outside. Located in the bathroom is a large airing cupboard with bifold louvre doors. This houses the 150L Stelflow unvented hot water cylinder, central heating pumps, expansion vessels and UFH manifold. Fitted out with slatted shelves, it provides generous drying/storage space. Access is available via two removable panels behind the toilet. The grey water pump out is via a custom-made stainless steel drain box, fitted with a solid-state float switch, relay and washing machine pump, which is almost silent, and which has proved very reliable in operation.
Engine room
Home to the stunning Gardner 3LW and housing all of the major electrical components and batteries. Polished brass header tank and brass bulkhead lamp. Heavy duty gearbox oil cooler. Underfloor storage for paints, etc. Plus washing line for efficient drying of laundry and wet clothing!
4 – 6 hours cruising is normally sufficient to heat the entire 150L hot water cylinder to 60C.
Back cabin area (Utility room)
The back cabin houses a 5Kg washer-dryer and domestic 240V 3-drawer freezer, with storage space above, plus two wardrobes. Under the stern steps is additional storage for mooring equipment, windlasses, etc. The stern steps can be easily removed to allow access to the prop shaft and thrust bearing. Spotlight and bulkhead light.
Solid brass speedwheel and push-pull gear controls.
Electrical control panel with voltmeters, digital ammeter, horn and light switches, crew call buzzer and USB socket. There is a useful fold-down perch seat and ticket cupboard space. The stern doors are 610mm wide, to allow appliances to be taken in and out of the boat.
60’ x 6’ 10”, craftsman built by XR&D to a custom specification, launched October 2018. 10:6:4 construction on a 208cm baseplate. The square-sided construction means the hull sides are vertical, giving an extra 3” width at floor level. The hull has a 9’ 6” bow swim and a 10’ S-shaped stern swim. This design forms a knife edge at the stern gland, to help present ‘clean’ water to the prop. The boat is hydrodynamically efficient, producing very little disturbance at canal cruising speed. The boat has square gunwales, to provide increased effective width.
The hull is semi-riveted with scrolled cants and other traditional details.
Ballast is 100mm high density concrete blocks, plus 3 x 56lb iron weights for trimming.
Traditional stern, with spacious Potter’s locker at the bow. Cabin sides are a full 1 metre, with ‘rattrap’ grabrails. This detail preserves the interior headroom, which is 6’ 4” max. The bow holds a huge 720L diesel stainless steel diesel tank. A 1,000L stainless steel water tank is located under the well deck.
A side hatch is located on the starboard side, and the engine room has a pigeon box and two ‘duck feeders’.
At the stern, there is access to the weed hatch and additional storage. This space is unencumbered by the usual fuel tank.
Glazing: Solid brass Houdini hatch, 7 x 15” solid brass drop-back portholes, 2 x solid brass front door windows. Two fixed brass ports in the back cabin. All double glazed.
The boat is gas-free.
The entire boat is lined out with 50mm of Celotex to provide impressive insulation, both against the cold in winter and heat from the sun in summer.
Cruising inventory
The boat is to be sold ‘ready to go’. Included in the sale are alloy windlasses and holders; 2 x lifejackets; throwing strop; nappy pins, chains, mooring spikes, shoreline cable; anchor, chain and warp; numerous mooring lines; hose; pipe and bottle fenders; various keys; anti-vandal keys; grappling hook; boat poles, etc. There is also a comprehensive set of map books and guides.
1962 Gardner 3LW, 3-cylinder, 42HP with traditional brass speedwheel and push-pull controls. With polished alloy rocker box cover and chromed sprayer pipes. The engine was rebuilt by Walsh’s of Manchester in 2018 and is fitted with 24V electric start. The gearbox is a 1.5:1 PRM 500 driving a 20” custom-made Crowther propeller, via an R&D drive plate (replaced new in 2025), Wilson prop shaft and thrust bearing. The stern gland is a traditional packed and greased type, with manual greaser.
An inline Fuel Guard eliminates water from the fuel. The fuel/return lines to the bow tank are 10mm PVC coated copper tube, sheathed in hardened polypropylene pipe.
The engine is very successfully cooled by a baffled skin tank of some 16sq. ft. and can be run at full power for extended periods without overheating (e.g. Ribble Link.) An additional thermostatically controlled 24V circulating pump assists water to flow through the coil of the hot water cylinder.
Electrical system
Low voltage electrics are 24V throughout. 240V AC is widely distributed through the boat via 31 x 13A outlets, a number of which have USB ports in addition.
Inverter: 5KW Victron Multiplus 24/5000/120. The input can be switched between shoreline and generator. The output is routed through an RCD-protected consumer unit. The shoreline entry point is RCD protected. When in Charge mode, a trickle charge is routed to the starter batteries to keep them at ‘float’.
Batteries: 12 x extreme duty 960Ah 2V traction cells (app. 26KWh storage), fitted new in Sept 2019. Starter batteries are 2 x 12v cells in series.
Battery management: Victron BMV 712 Smart with a 500A smart shunt. A Victron CGX colour display provides comprehensive information about the system and its history. Alternator temperature monitoring and battery temperature and midpoint voltage monitoring.
The battery monitoring system can be accessed using the Victron phone app via Bluetooth and over the internet via Victron VRM.
Alternator: 155A @ 24V. The output from the alternator is routed through a 200/24 Sterling A2B (alternator to battery) controller. This converts the alternator into a sophisticated multi-stage charger for the domestic batteries and gives priority to recharging the starter batteries in the first instance. Hot air from the alternator is vented into the airing cupboard.
All 24V circuits are protected by isolation switch, mega fuses and a switch/breaker panel. 24V wiring has been installed down the length of the boat in ceiling-mounted PVC conduit. 240V ‘arctic’ cabling is installed in PVC conduit behind the hull side panelling.
Lighting: Bedazzled LED lights throughout the interior. There are 18 ceiling-mounted warm white downlighters, which provide excellent illumination when required. Super bright tunnel light, 2 x steaming lights, plus navigation lights outside. PIR solar lighting in the well deck.
A 5KW diesel generator is mounted on sliding rails in the Potter’s locker. This has a 24V cooling fan. The enclosure is baffled and sound insulated. There is a 24V socket to allow connection of a fuel transfer pump for the generator.
Solar: 3 x 440W panels, feeding a Victron Smart 100/50 MPPT controller. On a good summer’s day, this system can produce over 7KWh of energy.
All 240V electrics were installed by a qualified electrician.
A galvanic isolator is installed.
Safety and security
The front doors and Potter’s Locker are fitted with welded-in 5-lever mortice locks. All other doors and hatches are secured with bolts from the inside.
Fire safety: 3 x 2Kg dry powder fire extinguishers and fire blanket; 2 x FireAngel CO detectors and one smoke alarm.
Fuel security: Owing to the location of the fuel tank in the bow – which is where the gas bottles would normally be kept – there is no external filler cap which can be compromised, minimising the likelihood of fuel theft.
Two high-capacity bilge pumps are installed, one in the stern and one next to the grey water drain box.
Two powerful 24V horns are mounted in front of the Potter’s locker.
Two automatic life jackets and a throwing strop are included.
Whilst due care has been taken in compiling the above details no guarantee can be given as to the accuracy by ourselves or the owner. Buyers are advised to obtain a survey before completing their purchase. To proceed without so doing is at their own risk and without recourse to ourselves or our clients. No guarantee is given by ourselves or our clients as to the condition of the boats or equipment therin.
Note: Indicated location is approximate general area only.